Industry Insights

Industry Insights

Why do 3D printing and machining work together?

Why do 3D printing and machining work together?

If you’ve printed a metre-scale polymer part that must bolt to something or seal against it, some features may need machining to fit. Printing builds the main shape without a mould or pattern; machining brings critical surfaces to size. Plan both steps from the drawing stage, alongside material selection and any inspection, testing or approval the application needs. 

Do 3D printed parts need machining? 

Some do and some don’t. It depends on whether the printed part meets the drawing’s requirements. Large format polymer parts are often printed near net shape, meaning close to their final dimensions. The extruder lays down beads typically several millimetres wide, leaving visible bead and layer lines. Shrinkage during cooling depends on the polymer, fibre content and part geometry. Machine positioning, calibration, structural stiffness and print settings also affect accuracy. These effects can be significant on metre-scale parts, but the tolerance for each feature determines whether machining is needed. 

For a planter or enclosure skin, the printed finish may be acceptable, or a sand and a coat may be enough. A hull below the waterline may need fairing and coating for drag and durability. Formwork transfers its texture to the concrete, so filling, coating or machining may be needed for the specified finish. For flanges, bearing seats and O-ring grooves, machining is about dimension and fit. 

Published work on fused granular fabrication (FGF) found that robotic milling improved the surface quality and dimensional accuracy of printed glass-fibre-reinforced polypropylene parts. [1] This supports the approach but does not establish performance for Hyperion’s systems or a particular metre-scale part. 

Which features usually need machining? 

Mating and sealing surfaces.
Flanges and mounting pads need faces flat and smooth enough to carry the load evenly. Gasket faces and O-ring grooves need particular attention because bead texture can create leak paths. Flat faces may be face-milled and grooves cut to the required profile. Machining alone does not establish leak-tightness; the material, printed structure and seal design matter too. 

Holes and threads.
Locating holes are often drilled, reamed or bored to meet size, roundness and position requirements. Clearance holes may pass as printed. Fine fastening threads are generally unsuitable for direct printing at this bead size. They can be tapped into sufficiently solid printed material or replaced by inserts or through-bolts to suit the loads and assembly. 

Datums.
The drawing’s datum features provide references for locating, fixturing and inspecting the part. Faces or holes can provide these references. Where printed features are unsuitable, datum features are established early in machining. Other features are then cut and measured relative to them. Agreeing this strategy before printing keeps the part, machining program and inspection report aligned. 

Interfaces with other components.
Bearing seats, shaft bores, insert pockets and openings for hatches, windows or equipment may need cut edges or sized recesses for fit. Trimming the part off the build plate and cutting openings for assembly also need planning. 

How are printing and machining sequenced in practice? 
The part is printed with a machining allowance: extra material on surfaces that will be cut to final size. This must account for print variation and leave enough wall thickness after cutting. Holes, threads and inserts need enough solid material around them for machining and service loads, using extra perimeter beads or filled regions. The part is left to cool and stabilise before cutting, because machining it warm risks further movement as it cools. 

The drawing identifies machined features and sets suitable dimensions and finishes for surfaces left as printed, avoiding unnecessary precision. Settle the datum strategy before writing the toolpath and check tool access. An unreachable face may require a different orientation or a split part. Choose layer direction with both service loads and machined faces in mind. 

Hyperion’s capabilities include multi-axis robotic machining and post-processing. Confirm the equipment, finishing location and required accuracy during scoping, so allowances, datums and toolpaths are planned before the first bead is laid. 

When does additive, subtractive, or a combined approach make the most sense? 

Printing on its own.
Machining may not be needed when printed dimensions and the printed or coated surface meet the specification. Examples include planters, enclosures with generous clearances and architectural panels. Some hulls and formwork can also meet their requirements with surface finishing alone. 

Machining on its own.
This may be simpler for small parts, parts with tight tolerances on most surfaces, or where suitable stock or a casting is readily available. If a printed polymer part needs machining all over, compare total costs with machining from stock. Setup work and the amount removed can change the result. 

Printing and machining together.
This suits large polymer parts with complex geometry and a few critical interfaces, including structural parts, tooling and infrastructure components. Printing builds the bulk without a mould or pattern; machining brings the interfaces to size. Cutting tools, fixtures, programming, finishing and inspection still belong in the cost comparison. Less machining can strengthen the case but compare total cost and lead time with the best alternative. 
The principle also applies to metal: wire arc additive manufacturing (WAAM) builds a near net shape component, then interfaces are machined as required. 

What should you ask a supplier about finishing and inspection? 

Whoever prints the part should be able to answer these before the quote is accepted. The answers help clarify the production scope and what the quote includes. 

Hyperion’s capabilities include materials testing, validation and inspection. Agree the job’s dimensional checks, material records and any repeatability testing during scoping. 

Supplier finishing and inspection checklist showing questions to ask and what a good answer looks like.

Talk to Hyperion about your part, which faces have to fit and what the drawing requires. For TitanCell or a custom robotic cell, include finishing and inspection alongside printing when defining the scope. 


Frequently asked questions 

Do 3D printed parts need machining? 

Some do, particularly mating faces, locating holes and sealing surfaces that cannot meet requirements as printed. Clearance holes and other surfaces may need no machining. Sanding, filling or coating can be enough where surface finish is the main concern. 

Why do large format 3D printed parts have visible layer lines? 

The extruder deposits beads several millimetres wide in layers, leaving a ribbed surface. Where this affects fit, flow or appearance, sanding, filling, coating or machining can provide the required finish. 

What is a machining allowance in 3D printing? 

Extra material printed on surfaces that will be cut to final size. Plan it during design, alongside datum features and solid material around holes and inserts. 

Can threads be 3D printed in large format parts? 

Coarse threads may be printable, but fine fastening threads are generally unsuitable at typical large-format bead sizes. Threads can be tapped into sufficiently solid printed material, or replaced by threaded inserts or through-bolts, depending on the load and assembly requirements. 

How accurate are large format 3D printed parts? 

Accuracy depends on machine positioning and calibration, print settings, material shrinkage, geometry and part size. There is no universal tolerance. Where the printed result cannot meet the drawing, machining can bring critical features to size. Agree and verify the achievable accuracy for the job. 

Is it cheaper to print and machine a part, or machine it from solid? 

It depends on the geometry and how much machining is needed. Printing a large polymer part and machining a few critical faces can reduce material removal compared with cutting from solid. Include programming, fixturing, finishing and inspection in the comparison. For small parts or tight tolerances on most faces, machining from stock is often simpler. 

Do WAAM metal parts need machining as well? 

Often, especially for close-fitting interfaces. Wire arc additive manufacturing builds a near net shape metal component. Mating faces, bores and sealing surfaces are then machined where required. Plan any heat treatment and inspection to suit the material and application. 

Can printing and machining be done in the same cell? 

Yes, using interchangeable tools or separate heads or robots in a suitably equipped system. Polymer parts need time to cool and stabilise before finish machining. A separate setup may better suit the part’s size, access or accuracy requirements. Confirm the equipment and finishing location when scoping a Hyperion deployment. 

How are printed and machined parts inspected? 

Against the drawing, checking machined features against their dimensions and tolerances, and printed surfaces against their dimensional and finish requirements. Agree the inspections, dimensional reports and material records during scoping. 

References 

[1] Zhang, R. et al. (2026). Six-Axis Robotic Milling for Enhancing Surface Quality and Dimensional Accuracy of Fused Granular Fabrication Parts. Polymers, 18(5), 608. https://doi.org/10.3390/polym18050608